Keurig K10 User Manual

Owner’s manual  
Keurig® K-CupK10 MINI Plus Brewer  
Important SafeguardS Safe Operation & Use  
When using electrical appliances, basic  
safety precautions should be followed,  
including the following:  
11. For best operation, plug the appliance  
into its own electrical outlet on a  
dedicated circuit to prevent flickering  
of lights, blowing of fuses or tripping a  
circuit breaker.  
electrical short circuit, grounding  
reduces the risk of electrical shock.  
19. If the outlet is a standard 2-prong wall  
outlet, it is your personal responsibility  
and obligation to have it replaced with a  
properly grounded 3-prong wall outlet.  
20.Do not, under any circumstances, cut or  
remove the third (ground) prong from  
the power cord or use an adapter.  
21. Consult a qualified electrician if  
the grounding instructions are not  
completely understood, or if doubt  
exists as to whether the appliance is  
properly grounded.  
CAUTION: There are two sharp needles that puncture the  
K-Cup® pack, one above the K-Cup® Pack Holder and the  
other in the bottom of the K-Cup® Pack Holder. To avoid risk  
of injury, do not put your fingers in the K-Cup® Pack  
Assembly Housing.  
WARNING  
WARNING  
KEEP ALL PLASTIC BAgS AwAY FROM CHILDREN.  
THIS PRODUCT CONTAINS CHEMICALS, INCLUDINg  
LEAD, wHICH IS KNOwN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,  
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.  
1. Read all instructions before using.  
2. Do not touch hot surfaces. Use handles  
and knobs when available.  
12. Do not operate any appliance with a  
damaged cord or plug or after  
the appliance malfunctions or is  
damaged in any manner. Contact  
Keurig Customer Service to report  
any malfunction of or damage to the  
brewer.  
13. Do not let the cord hang over the edge  
of the table or counter, or touch hot  
surfaces.  
CAUTION: There is extremely hot water in the K-Cup® Pack Holder during  
the brew process. To avoid risk of injury, do not lift the Handle or open the  
K-Cup® Pack Assembly Housing during the brewing process.  
3. This appliance must be properly  
installed and located in accordance  
with these instructions before it is used.  
4. The use of accessory attachments  
not recommended by the appliance  
manufacturer may result in fire,  
electrical shock or injury to persons.  
5. Do not place on or near a hot gas or  
electric burner, or in a heated oven.  
6. Do not use outdoors.  
CAUTION: Please always keep the brewer in its upright position to avoid  
potential injury and/or damage to your brewer.  
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to  
reduce the risk of becoming entangled in or tripping over a longer cord.  
22.Do not use the appliance for other than  
its intended use.  
WARNING TO USERS AND PARENTS  
1. DO NOT permit children to use brewer unless there is adult  
supervision. Brewer dispenses very hot water.  
If an extension cord is used, (1) the marked electrical rating of the cord set or  
extension cord should be at least as great as the electrical rating of the  
appliance; (2) the cord should be arranged so that it will not drape over the  
countertop or tabletop where it can be pulled on by children or tripped over  
unintentionally; and (3) the extension cord must include a 3-prong grounding plug.  
14. To disconnect, press the Power Button  
on the brewer to “OFF” status and then  
remove the plug from the wall outlet.  
7. To protect against fire, electric shock  
SAvE THESE  
2. SPECIAL NOTICE FOR HOT COCOA USERS:  
and injury do not immerse cords, plugs, 15. Close supervision is necessary when  
IMMEDIATELY AFTER USING A HOT COCOA K-CUP® PACK, RUN a Hot  
Water Brew Cycle without a K-Cup® pack to avoid the possibility of  
clogging the exit needle. DO NOT assume the next user will do this.  
INSTRUCTIONS.  
or the appliance in water or any other  
liquid.  
any appliance is used by or near  
children.  
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.  
8. Do not overfill the Cold Water Reservoir 16. Do not lift the brewer Handle while  
with water.  
brewing is in progress; scalding  
may occur.  
9. Use only water in this appliance! Do  
not put any other liquids or foods in the  
Water Reservoir except as instructed in  
the Cleaning Instructions in this guide.  
10. Turn off and unplug the brewer before  
cleaning or maintenance. Allow to cool  
before putting on or taking off parts  
and before cleaning the appliance.  
17. Always keep the Cold Water Reservoir  
Lid closed unless you are refilling it.  
18. This appliance is equipped with a power  
cord having a grounding wire with a  
grounding plug. The appliance must  
be grounded using a 3-hole properly  
grounded outlet. In the event of an  
WARNING: TO REDUCE THE RISK OF FIRE OR  
ELECTRIC SHOCK, DO NOT REMOVE THE  
BOTTOM COVER. NO USER SERVICEABLE  
PARTS ARE INSIDE. REPAIR SHOULD BE DONE  
BY AUTHORIZED SERVICE PERSONNEL ONLY.  
WARNING  
RISK OF FIRE OR  
ELECTRIC SHOCK  
!
DO NOT OPEN  
2
3
SeCtIon 1 Brewer Overview  
table of ContentS  
J
A
B
A
B
C
D
E
F
G
H
I
Water Level Guide  
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM  
K10 MINI Plus Brewer — Using Your Brewer  
K
Handle  
SeCTion 1—Brewer overview ..........................................................4  
SeCTion 2Helpful Hints .................................................................6  
SeCTion 3—Buttons & indicators.........................................................7  
K-Cup® Pack Holder Assembly  
K-Cup® Pack Holder  
Funnel  
L
SeCTion 4—Set-Up & operation  
Initial Cleansing & First Brew...........................................................8  
K-Cup® Pack Assembly Housing  
Drip Tray Overfill Indicator  
Drip Tray Plate  
M
N
D
E
SeCTion 5—Cleaning & Maintenance  
C
Cleaning External Parts ..................................................................12  
Cleaning the K-Cup® Pack Holder Assembly .............................. 12  
Cleaning the Cold Water Reservoir................................................14  
Emptying the Internal Hot Water Tank...........................................14  
De-Scaling Your Brewer ..................................................................14  
Storage ...............................................................................................15  
Storing the Power Cord....................................................................15  
F
Drip Tray  
O
J
Cold Water Reservoir Lid  
Cold Water Reservoir  
BREW Button  
G
H
K
L
M
N
O
P
SeCTion 6—Troubleshooting..........................................................16  
SeCTion 7—Warranty......................................................................18  
LED Indicator  
Power Button  
Record your Brewer Serial Number here.  
I
P
Power Cord  
Drip Tray Base  
Removing the serial number label from the brewer will void warranty.  
4
5
SeCtIon 3 Buttons & Indicators  
SeCtIon 2 Helpful Hints  
1. Plug Power Cord into an independent,  
Grounded outlet – If the electric circuit is  
overloaded with other appliances, your brewer  
may not function properly.  
up to 30% more ground coffee than regular  
varieties) along with a brew size that’s right for  
you. The less water you use, the more intense  
the flavor in your cup. The more water you use,  
the less intense the flavor in your cup.  
10. Automatic Shut-off – As a safety feature, your  
brewer will shut off automatically when it is  
idle for longer than 90 seconds. Simply press  
the Power Button to restart.  
Power Button (does not illuminate)  
Press to turn the brewer power on and off.  
Add Water Indicator  
Your Next Brew  
When the brewing process is complete, the Add Water  
Indicator light will appear. At this point you can begin  
making the next beverage, or you can power off.  
2. initial Cleansing Brew – Before you make your  
first beverage, perform an initial cleansing  
brew without inserting a K-Cup® pack.  
11. Clean Your Brewer Regularly – To keep  
your brewer looking and performing at its  
best, be sure to clean the external and  
internal components on a regular basis.  
See page 12 for more information.  
Use the Water Level Guide located inside the Cold  
Water Reservoir to customize your brew size.  
Flashing Blue — Fill the Cold Water Reservoir  
with cold water until it reaches just under the rim  
of the desired level – 6, 8, or 10 oz. of the Water  
Level Guide.  
Automatic Shut-Off  
6. Brewing iced Beverages – Your iced tea and  
iced coffee taste best when fresh-brewed hot  
over ice. Try it by placing a tall cup filled with  
ice on the Drip Tray, choose your favorite  
K-Cup® pack and follow the brewing  
3. one Cup at a Time – Your new brewer makes  
one fresh beverage at a time. You will need to  
add fresh water each time you brew. Unlike  
other Keurig® brewers, the K10 MINI Plus does  
not store water in the reservoir.  
As a safety feature, your brewer will automatically  
shut off at any stage when it is idle for longer than 90  
seconds. Press the Power Button to restart. If it shut  
off while the BREW Button was flashing blue, lift and  
lower the Handle to reset.  
12. De-Scaling – Depending on the mineral  
content of the water in your area, calcium  
deposits or scale may build up in your brewer.  
Scale is non-toxic, but left unattended, it can  
hinder brewer performance. De-scaling your  
brewer helps maintain the heating element  
and other internal parts of the brewer that  
come in contact with water. See page 14 for  
more information.  
Handle Indicator  
instructions on page 8. Also, look for the  
“Brew Over Ice” icon on K-Cup® packs specially  
crafted to brew over ice! IMPORTANT: Do not  
brew into a cup made of glass. Doing so may  
cause the glass to crack or break.  
4. The Right Water Makes a Difference – For the  
best-tasting gourmet coffee, tea or hot cocoa,  
Keurig recommends using bottled or filtered  
water. We do not recommend using distilled or  
reverse osmosis water. Note that water quality  
can vary from place to place. If you notice an  
undesirable taste in your beverage (such as  
chlorine or other mineral substance), we  
recommend trying bottled water or water from  
a filtration system. For best results, carefully  
follow manufacturer’s instructions when using  
any water filtration system.  
Flashing Blue — The blue light flashes when the  
minimum water amount of 6 oz. has been poured  
into the Cold Water Reservoir. After adding your  
desired amount of water (10 oz. maximum),  
lower the Cold Water Reservoir Lid. The light will  
continue to flash until you lift the Handle.  
Drip Tray Overfill Indicator  
A red float will appear when the Drip Tray is almost  
full. Carefully slide Drip Tray out and empty contents  
into the sink.  
7. Remove K-Cup® Pack After Use – Please see  
page 8 for brewing instructions.  
13. Storing – When storing your brewer,  
empty the Drip Tray. Follow the instructions  
on page 14 for emptying the Internal Hot  
Water Tank. Store your brewer upright in  
a safe, dry, frost-free environment. See  
page 15 for more information.  
8. Brewing into a Tall Mug – To brew into a tall  
mug, simply remove the Drip Tray Assembly  
and place the tall mug on the Drip Tray Base.  
Without the Drip Tray Assembly, however, you  
do lose the benefit of the Drip Tray to contain  
any excess water.  
Brew Button  
Flashing Blue — Indicates you are ready to brew.  
Press the BREW Button.  
Flashing Red — Indicates water is heating  
(approximately 2 minutes).  
Solid Red — Indicates brewing and dispensing of  
beverage has begun.  
5. Customize Your Size, Flavor & Brew – With  
over 200 K-Cup® pack varieties and multiple  
fill levels, your brewer provides endless  
customization options – so that you can create  
the size, flavor and strength of each beverage  
that is perfect for you. For a strong, intense  
flavor, select an Extra Bold K-Cup® pack (with  
9. The Drip Tray – Any liquid overflow (from your  
cup or from the Cold Water Reservoir) will be  
caught in the Drip Tray. Be sure to empty the  
Drip Tray when the red Drip Tray Overflow  
Indicator pops up.  
6
7
For accurate measuring, do not fill if the  
Handle is up. In the down position it prevents  
water from entering the lower heating  
compartment.  
SeCtIon 4 Set-Up & Operation  
Initial Cleansing & First Brew  
MAX  
10 oz.  
CAUTION: Two sharp needles are used to puncture the  
K-Cup® packs. One is above the K-Cup® Pack Holder and  
the other is in the bottom of the K-Cup® Pack Holder. To  
avoid risk of injury, do not put your fingers inside the  
K-Cup® Pack Assembly Housing.  
8 oz.  
BREW  
CAUTION: During the brewing process, the water  
gets extremely hot. To avoid risk of injury, do not  
lift the Handle or open the K-Cup® Pack Assembly  
Housing until brewing is complete.  
6 oz.  
Min  
Remove all tape and cardboard.  
1
2
3
4
Plug the Power Cord into an  
independent, grounded outlet.  
Press the Power Button. The Add Water Indicator  
will flash blue.  
Lift the Cold Water Reservoir Lid.  
Perform an initial cleansing  
brew before making your  
first beverage. Follow these  
instructions but do not insert  
a K-Cup® pack.  
Pour water anywhere within the Cold Water  
Reservoir until it reaches up to the rim of your  
desired fill level on the Water Level Guide  
(minimum of 6 oz.). Lower the lid.  
The Power Button does not illuminate.  
For accurate measuring, do not fill if the  
Handle is up.  
Bottled or filtered water is recommended;  
distilled or reverse osmosis water is not.  
8
9
SECTION 4 Set-Up & Operation (continued)  
Let water fully drain into brewer  
before lowering the Handle.  
Do noT remove foil lid or puncture K-Cup® pack.  
5 Sec  
2 Min  
5
10  
6
9
11  
7
8
Lift the Handle. Water starts to drain  
from the Cold Water Reservoir into  
the brewer.  
Place mug on the Drip Tray.  
Insert the K-Cup® pack into the  
K-Cup® Pack Holder.  
Wait until all water has drained  
(5 seconds) into the brewer  
before lowering the Handle  
completely.  
The BREW Button will flash blue. Press the  
BREW Button.  
The BREW Button will flash red to  
indicate that the water is heating. After  
about 2 minutes, the BREW Button will  
turn solid red when the beverage starts  
to dispense.  
Enjoy your beverage! Your brewer is ready to use  
again or you can power it off.  
If you want to use a taller mug,  
you can slide the Drip Tray out,  
but you will lose the benefit of  
the tray to catch the excess  
water.  
Do not add a K-Cup® pack if  
you are performing the initial  
cleansing brew.  
As a safety feature, brewer automatically  
shuts off after 90 seconds.  
!
CAUTION: Do not lift the Handle  
If you add more than 10 oz.,  
excess water goes into the  
Drip Tray.  
while brewing.  
Remove used K-Cup® pack after brewing.  
CAUTION: K-Cup® pack will be hot.  
If completing the initial cleansing brew,  
discard hot water into the sink. Your brewer  
is ready to use again.  
10  
11  
SeCtIon 5 Cleaning & Maintenance  
Cleaning External Parts  
Cleaning the K-Cup® Pack Holder Assembly  
2. Separate the Funnel from the K-Cup® Pack Holder by pulling it until it  
snaps free (fig. 2).  
4. To replace the Funnel, just snap it back into the K-Cup®  
Pack Holder (fig. 4).  
IMPORTANT: Make sure the brewer is unplugged before cleaning.  
K-Cup® Pack Holder Assembly parts include:  
Funnel  
IMPORTANT: Make sure the brewer is unplugged before cleaning.  
Regular cleaning of the brewer’s external components is recommended.  
Brewer external housing  
3. Clean the Exit Needle on the bottom of the K-Cup® Pack Holder. Insert  
a paper clip (fig. 3) or similar tool from below if needle becomes  
clogged by coffee grinds.  
fig.  
4
K-Cup® Pack Holder with Exit Needle  
Drip Tray  
Drip Tray Plate  
The K-Cup® Pack Holder Assembly parts can be placed on  
the top shelf of the dishwasher. Use a low temperature cycle  
when cleaning.  
BReWeR  
fig.  
fig.  
2
3
Never immerse brewer in water or other liquids.  
Clean the external housing of the brewer and other external  
components with a damp, non-abrasive, lint-free cloth.  
1. To remove the K-Cup® Pack  
5. To replace the K-Cup® Pack Holder Assembly, align the  
K-Cup® Pack Holder with the opening using the two front  
ribs as a guide and snap into place from the top (fig. 5).  
Holder Assembly from the brewer,  
lift the Handle to open. Grasp the top  
of the K-Cup® Pack Holder with one  
hand. With the other hand, push up  
on the bottom of the K-Cup® Pack  
DRiP TRAY AnD DRiP TRAY PLATe  
fig.  
1
When the red Drip Tray Overfill Indicator appears, the Drip Tray is  
almost full. Carefully remove by sliding tray toward you. Empty  
contents into the sink.  
fig.  
5
Inspect the Drip Tray periodically and clean with a damp, non-abrasive,  
lint-free cloth.  
Holder Assembly until it releases (fig. 1).  
Avoid sharp needles in K-Cup®  
Pack Assembly Housing. Do  
not put your fingers inside the  
K-Cup® Pack Assembly Housing.  
Do not put the Drip Tray or the Drip Tray Plate in the dishwasher.  
12  
13  
SECTION 5 Cleaning & Maintenance (continued)  
Cleaning the Cold Water Reservoir  
Emptying the Internal Hot Water Tank  
De-Scaling Your Brewer (continued)  
Storage  
FiLL, CLeAn AnD RinSe  
Step 1: First Vinegar Rinse  
it is normal over time for discoloration, spotting or staining to appear in  
the Cold Water Reservoir. Results will vary depending on the mineral  
content of the bottled or filtered water used but will not affect the  
operation of the brewer. However, be sure to clean the Cold Water  
Reservoir regularly to minimize build-up.  
Brewer must be powered off but plugged in.  
Lower the Cold Water Reservoir Lid.  
Place a mug on the Drip Tray.  
Empty the Internal Hot Water Tank and Cold Water Reservoir before storing.  
See page 14. Store your brewer in a safe, frost-free environment in an  
upright position.  
Fill the Cold Water Reservoir with 10 oz. of undiluted white vinegar.  
Place the ceramic mug on the Drip Tray.  
Lift the Handle, but do not add a K-Cup® pack.  
Press and hold down the BREW Button and continue to hold until all  
the water is dispensed into the mug.  
Storing the brewer in cold temperatures may cause any residual  
condensation to freeze inside the brewer and could cause damage.  
After 5 seconds, lower the Handle.  
Press the flashing blue BREW Button. It will flash red and then turn  
solid red.  
To access the Cold Water Reservoir, lift the lid. Remove the Water Level  
Guide (fig. 6) and then clean inside the reservoir with a damp, lint-free cloth  
as necessary (fig. 7).  
Before using your brewer after storage, wipe the Cold Water Reservoir with a  
damp, lint-free cloth and run three (3) cleaning brews (without K-Cup®  
packs). See page 8 for initial cleansing brew process.  
There will be a 3 to 5 second delay before water begins to dispense.  
Once the vinegar is dispensed, discard hot contents into sink.  
Step 2: Second Vinegar Rinse  
Replace the Water Level Guide and lower the lid when finished.  
Pour the remaining 10 oz. of vinegar into the Cold Water Reservoir.  
Place the ceramic mug on the Drip Tray.  
Let brewer rest at room temperature for at least 2 hours before  
powering on.  
De-Scaling Your Brewer  
Lift the Handle, but do not add a K-Cup® pack.  
The Water Level Guide is not dishwasher safe.  
Calcium deposits may build up in your brewer, depending on the mineral  
content of your water. Scale is non-toxic but if left unattended, it can hinder  
brewer performance. De-scaling your brewer helps to maintain the heating  
element and other internal parts of the brewer.  
After 5 seconds, lower the Handle.  
Press the flashing blue BREW Button. It will then flash red.  
When it turns solid red, power off as it starts to dispense.  
Storing the Power Cord  
fig.  
fig.  
6
7
Allow brewer to sit for 30 minutes.  
Behind the brewer is a convenient  
compartment to hold the Power  
Cord during transport or storage  
(fig. 8).  
fig.  
8
Power on the brewer, lift and lower the Handle, then press  
BREW Button.  
Once the vinegar is dispensed, discard hot contents into sink.  
The de-scaling process should be done every 3 to 6 months to ensure  
optimal performance or when there are white deposits in the Cold Water  
Reservoir. However, it is possible for calcium deposits to build up faster,  
making it necessary to de-scale more often.  
Step 3: Fresh Water Rinse  
Fill the Cold Water Reservoir with 10 oz. of fresh water.  
Place the ceramic mug on the Drip Tray.  
Lift the Handle, but do not add a K-Cup® pack.  
To begin, you will need the following:  
20 oz. of undiluted white vinegar  
12 oz. ceramic mug (do not use a paper cup)  
Access to a sink  
Service  
Lower the Handle and continue the brewing process until the  
hot water is dispensed into the mug. Discard hot contents into sink.  
Repeat this cleansing brew process three (3) more times to cleanse the  
brewer plumbing and to remove any residual vinegar taste. The brewer  
is now ready for normal use again.  
Beyond these recommended cleaning and maintenance procedures, this  
brewer is not user serviceable. See page 18 for warranty guidelines. For  
service, please refer to the Warranty section in this guide.  
14  
15  
SeCtIon 6 Troubleshooting  
SiTUATion  
SoLUTion  
SiTUATion  
SoLUTion  
Brewer will not brew when used for the first time  
Brewer does not have power  
Make sure the Power Button is pressed. The Add Water Indicator should flash blue  
after pushing the Power Button. Note that the Power Button does not illuminate.  
During normal operation, the brewer will shut off when it is idle for longer than 90  
seconds. Just press the Power Button to restart.  
Brewer may be cold or frozen. Let brewer rest at room temperature for at least 2  
hours before powering on.  
Make sure the brewer has power (see previous page).  
Brewer only brews a partial brew  
Plug brewer into an independent outlet.  
Allow enough time for water in the Cold Water Reservoir to drain completely into the brewer.  
The Exit Needle may be clogged (see page 12).  
Check to be sure that brewer is plugged in securely.  
Plug into a different outlet.  
Clean the K-Cup® Pack Assembly, if necessary (see page 12).  
De-scale the brewer (see page 14).  
If you have repeated the de-scale procedure two times and the brewer still does not  
function properly, contact Customer Service.  
Reset your home circuit breaker, if necessary.  
If the brewer still does not operate, contact Customer Service.  
BReW Button flashes red too long  
Under normal operation, the BREW Button will flash red when the brewer is heating and  
will turn solid red when brewing. If the BREW Button flashes red longer than 3 minutes,  
contact Customer Service.  
Under normal operation, the brewer will shut off when it is idle for longer than 90 seconds.  
Just press the Power Button to restart.  
If the brewer shuts off in the middle of a brew (not from power outage), contact Customer Service.  
Brewer shuts off automatically  
There is water in the Drip Tray  
Add Water indicator does not flash blue  
If the Add Water Indicator does not flash blue, make sure the brewer has power (see above).  
Water may be in the Cold Water Reservoir and brewer. First, try raising the Handle to  
drain all water from the Cold Water Reservoir into the brewer. If the light still does not flash,  
power off and place a mug on the Drip Tray. Hold down the BREW Button and continue to  
hold down until all the water is dispensed into the mug.  
Remember that any liquid overflow (from your cup or the Cold Water Reservoir) will be  
caught in the Drip Tray.  
When the Drip Tray is almost full, the red Drip Tray Overflow Indicator will appear. Carefully  
remove the Drip Tray and empty its contents into the sink.  
If the brewer still does not operate, contact Customer Service.  
Red indicator appears in Drip Tray  
This means that the Drip Tray is almost full. Carefully remove the Drip Tray and empty its  
Brewer will not brew  
Make sure the brewer has power (see above).  
contents into the sink.  
If using reverse osmosis or distilled water, the brewer may not operate correctly. See page 14 for  
emptying the Internal Hot Water Tank and then use filtered or bottled water.  
Press the Power Button. If the Add Water Indicator flashes blue, add water and attempt  
to brew. If the brewer loses power during the brew process, the brewer may need to be  
re-set when power is restored. To re-set, simply lift and lower the Handle.  
Check that the minimum water level of 6 oz. has been poured into the Cold Water Reservoir.  
Should other issues arise with your brewer, please call  
Keurig Customer Service at 1.866.901.BReW (2739).  
16  
17  
Scan. Click. Call!  
SeCtIon 7 Warranty  
Learn more and reach us quickly without leaving home.  
Limited One Year Warranty  
Keurig, Incorporated warrants that your brewer will be free of defects in  
materials or workmanship under normal home use for one year from the date  
of purchase. It is recommended that you fill out and return the warranty card  
enclosed with your brewer so that your purchase information will be stored  
in our system. Keurig will, at its option, repair or replace a defective brewer  
without charge upon its receipt of proof of the date of purchase. If a  
replacement brewer is necessary to service this warranty, the replacement  
brewer may be new or reconditioned. If a replacement brewer is sent, a new  
limited one year warranty will be applied to the replacement brewer.  
Nor does this warranty cover damages caused by non Keurig Brewed®  
K-Cup® brand packs or accessories, services performed by anyone other  
than Keurig or its authorized service providers, use of parts other than  
genuine Keurig® parts, or external causes such as abuse, misuse,  
inappropriate power supply or acts of God.  
other limitations  
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS  
WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY  
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO  
YOUR K10 MINI PLUS BREWER, INCLUDING ANY IMPLIED WARRANTY OF  
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some  
states or provinces do not allow disclaimers of such implied warranties or  
limitations on how long an implied warranty lasts, so the above limitation  
may not apply to you depending on the state or the province of purchase.  
This warranty only applies to brewers operated in the United States and  
Canada. This warranty gives you specific legal rights, and you may also have  
other rights that vary from state to state and, in the case of Canada, from  
province to province.  
Only the use of Keurig Brewed® K-Cup® brand packs and accessories will  
guarantee the proper functioning and lifetime of your Keurig® brewer.  
Any damage to or malfunction of your brewer resulting from the use of non  
Keurig Brewed® K-Cup® brand packs and accessories may not be covered  
by this warranty or may result in a service fee if the damage or malfunction is  
determined to be caused by such use.  
Scan here for videos about caring for your brewer!  
Have questions? We’re here to help!  
Scan this QR code with your smartphone for step-by-step videos on  
cleaning, de-scaling and more. Or if you prefer, you can watch the videos  
on your computer at bit.ly/NjTZ8W  
Keurig is committed to your satisfaction. If you have questions, just give  
us a call to have them answered quickly without leaving the comfort of  
your home. 1.866.901.BREW (2739)  
How do you obtain warranty service?  
Keurig® brewers are high-quality appliances and, with proper care, are  
intended to provide years of satisfying performance. However, should the  
need arise for warranty servicing, simply call Keurig Customer Service at  
our toll free phone number 1.866.901.BREW (2739). Please do not return your  
brewer for servicing without first speaking to Keurig Customer Service to  
obtain an Authorization to Return number (ATR). Keurig® brewers returned  
without an ATR number will be returned to the sender without servicing.  
What is not covered by the limited warranty?  
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL  
DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER  
INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH  
OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces  
do not allow the exclusion or limitations of incidental or consequential  
damages, so the above limitation or exclusion may not apply to you  
depending on the state or province of purchase.  
Keurig, Incorporated  
55 Walkers Brook Drive  
Reading, MA 01867  
1.866.901.BREW (2739)  
18  
19  

Motorola GSM L2 User Manual
Microsoft Windows 7 Home Premium QGF 00154 User Manual
Maxtor External Storage X01FWRA080 User Manual
Fujitsu MAF3364FC User Manual
Emerson SmartSet CKD5811 User Manual
Bloomfield 2074L User Manual
Black & Decker ODC150N User Manual
Billy Goat KD Termite TKD Termite KD511SP TKD511SP User Manual
Addonics Technologies AD5SAPM User Manual
ABB VTR251 2 User Manual