INSTRUCTION BOOKLET
SS-300C
Compact Single Serve
For your safety and continued enjoyment of this product, always read the instruction book carefully before using.
cord into the wall outlet. To disconnect,
turn controls to Off, then remove plug
from wall outlet.
If a grounding-type outlet is not available, an
adapter, shown in Figure B, may be obtained
so that a 2-slot wall outlet can be used with
a 3-prong plug. As shown in Figure C, the
adapter must be grounded by attaching its
grounding lug under the screw of the outlet
cover plate.
SPECIAL CORD SET
IMPORTANT
INSTRUCTIONS
SAFEGUARDS
A short power-supply cord is provided to
reduce the risks resulting from becoming
entangled in or tripping over a longer cord.
12. Scalding may occur if the water filter
compartment cover is removed during
the brewing cycles.
When using electrical appliances, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock and/or
injury to persons, including the following:
13. Do not use appliance for other than
intended use.
Longer extension cords are available and
may be used if care is exercised in their use.
NOTE: Do not remove the grounding
prong.
1. READ ALL INSTRUCTIONS.
14. Do not lift handle to open the lid of the
brewer while brewing is in progress.
If a long extension cord is used, the marked
electrical rating of the extension cord must
be at least as great as the electrical rating of
the appliance. The extension cord should be
a grounding-type 3-wire cord, and the
longer cord should be arranged so that it will
not drape over the countertop or tabletop
where it can be pulled on by children or
tripped over.
2. Always unplug from outlet when not
in use and before cleaning. Allow to
cool before putting on or taking off
parts and before cleaning the
appliance.
CAUTION: Before using an adapter, it must
be determined that the outlet cover plate
screw is properly grounded. If in doubt,
consult a licensed electrician. Never use
an adapter unless you are sure it is
properly grounded.
15. Do not overfill the water reservoir with
water. Use ONLy WATER in this
appliance! Do not put any other liquids
or foods in the water reservoir except
as instructed in the cleaning instructions
in this guide.
3. Do not touch hot surfaces. Use handles
and knobs.
Note: Use of an adapter is not permitted in
Canada.
16. Do not clean drip tray with cleansers,
steel wool pads, or other abrasive
materials.
4. To protect against electric shock and
injury to persons, do not place cord,
plug, or base unit in water or other
liquids.
IMPORTANT UNPACKING
INSTRUCTIONS
1. Place the box on a large, sturdy, flat
surface.
A.
NOTICE
17. WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT
REMOVE THE BASE PANEL. NO
Circuit Grounding
Conductor
If you have a
5. Close supervision is necessary when
any appliance is used by or near
children.
diecast metal unit,
for your protection
it is equipped with
a 3-conductor cord
set that has
a molded 3-prong
grounding-type
plug, and should
be used in combi-
nation with a prop-
erly connected
grounding-type
outlet as shown
in Figure A.
Connected
Properly
USER-SERVICEABLE PARTS ARE
INSIDE. REPAIR SHOULD BE DONE
ONLy By AUTHORIZED PERSONNEL.
2. Remove the instruction book and any
other literature.
6. Do not operate any appliance with
a damaged cord or plug or after the
appliance malfunctions or has been
dropped or damaged in any manner.
Return appliance to the nearest
Cuisinart Repair Centre for examination,
repair, or electrical or mechanical
adjustment.
Grounding
Prong
B.
3. Turn the box so that the back side of
the brewer is down and slide the
coffeemaker from the box.
18. Do not operate your appliance in an
appliance garage or under a wall cabi-
net. When storing in an appliance
garage, always unplug the unit from
the electrical outlet. Not doing so
could create a risk of fire, especially if
the appliance touches the walls of the
garage or the door touches the unit as
it closes.
Adapter
Grounding Lug
4. After removing the brewer, place the
box out of the way and take the side
pulp molded inserts away.
C.
Cover
Mounting
Screw
7. The use of accessory attachments not
recommended by Cuisinart may cause
injuries, fire, electric shock or injury to
persons.
5. Remove the polybag covering the brewer.
We suggest you save all packing materials
in the event that future shipping of the
machine is needed. Keep all plastic bags
away from children.
Cover of
Grounded
Outlet Box
SAVE THESE
INSTRUCTIONS
FOR HOUSEHOLD
USE ONLY
8. Do not use outdoors.
9. Do not let cord hang over edge of table
or counter, or touch hot surfaces.
10. Do not place on or near a hot gas or
electric burner, or in a heated oven.
11. Always fill water reservoir first, then plug
WARNING
RISK OF FIRE OR ELECTRIC SHOCK
DO NOT OPEN
WARNING: RISK OF FIRE OR ELECTRIC SHOCK
The lightning flash with arrowhead symbol within an equilateral triangle is intended
to alert the user to the presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of fire
or electric shock to persons.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY
2
3
Element 1
Contents
Water
the Quest
Important Safeguards . . . . . . . . . . . . . . . . . . . . . 2
Important Unpacking Instructions . . . . . . . . . . . . 3
The Quest for the Perfect Cup of Coffee . . . . . . 5
Features and Benefits. . . . . . . . . . . . . . . . . . . . . 6
Buttons and Indicators . . . . . . . . . . . . . . . . . . . . 8
Setting Up Your Brewer . . . . . . . . . . . . . . . . . . . 9
Charcoal Water Filter . . . . . . . . . . . . . . . . . . . . . 9
Brewing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Hot Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Brewing with the My K-Cup® Reusable Filter . . 12
Cleaning and Maintenance . . . . . . . . . . . . . . . . 13
Cleaning External Parts . . . . . . . . . . . . . . . . 13
Cleaning the My K-Cup® Reusable Filter . . . 13
Cleaning the K-Cup® Holder . . . . . . . . . . . . 13
Cleaning the Water Reservoir . . . . . . . . . . . 14
Emptying the Internal Water Tank . . . . . . . . 14
De-Scaling Your Brewer . . . . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 16
Any hot beverage is made up primarily of water.
Often overlooked, the quality of the water is as
important as the quality of the coffee, tea or cocoa.
A good rule of thumb is that if your water doesn’t
taste good from the tap, it won’t taste any better
in your beverage. That’s why the Cuisinart® Compact
Single Serve has added a charcoal water filter that
removes chlorine, bad tastes and odors, for the
purest cup of coffee every time.
for the Perfect
Cup of Coffee
Element 2
Coffee
While the bulk of the liquid is water, all of the flavor
should be from the coffee, tea or cocoa. To achieve
the same great quality you receive at coffee bars,
you need to use the same quality ingredients. By
using the K-Cup®, brought to you by some of the
most premium brands on the market, you can be
assured that you’re getting the finest, freshest
gourmet product with every cup you brew. If you
choose to use your own coffee in the included
My K-Cup®, make sure all your ingredients are
at their freshest.
Element 3
Grind
The grind of coffee and cocoa, or the refinement of
your tea leaves, is critical for proper flavor extraction.
With the pre-measured, pre-ground ingredients
found in every K-Cup®, you can rest easy knowing
that it’ll brew perfectly each and every time, locking
in maximum flavor and freshness.
Element 4
ProPortion
No matter which cup size you choose, the Cuisinart®
Compact Single Serve, working in conjunction with
K-Cup®, always produces the perfect cup every
time. When grinding your own coffee and using it in
the included My K-Cup®, remember to add the
amount of ground coffee that corresponds to the
number of ounces being brewed.
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4
5
features and Benefits
1a
1a. Charcoal filter Holder
1b. Charcoal Water filter
2. reservoir Lid
2
3a. 10-ounce Water reservoir
with cup markings at
5
6, 8, and 10 ounces
4
1b
3b. Water Level Guide
4. Brewer Handle
5. Brewing Head
6. Brewing Chamber
holds My K-Cup® or
the K-Cup® Holder
3a
7. Housing
12
8. removable drip tray Plate
9. drip tray
15a
15b
6
10. drip tray Base
15c
16
11. drip tray overfill indicator
12. removable K-Cup® Holder
3b
13. My K-Cup® reusable
17
Coffee filter
14. My K-Cup® Compartment
14
conveniently stores My K-Cup®
15a. Led display
7
15b. add Water indicator
15c. K-cup® indicator
16. Brew Button
18
11
17. Hot Water Button
18. Power Button
8
10
19. Power Cord (not shown)
13
9
20. BPa free (not shown)
all materials that come in contact
with water or coffee are BPA free
6
7
Buttons and indicators
Setting Up Your Brewer
initial Cleaning and first Brew
Perform an initial cleaning before
making your first beverage. follow
these instructions but do not insert
a K-Cup®
.
Power Button (does not illuminate)
Press to turn the Brewer on and off.
1. Plug the power cord into an
independent, grounded outlet. Press
the Power button to turn the unit on.
Brew and Hot Water Buttons
When buttons are flashing blue it indicates
that a selection (Brew or Hot Water) needs
to be made. Once a selection is made
button is solid blue, indicating water is
heating and dispensing of beverage will
begin in approximately 2 minutes.
6. Wait until all the water has drained into
the brewer before lowering the brewer
handle completely.
7. Place mug on the drip tray.
8. The Hot Water button LED will remain
on, indicating that the water is heating.
After about 2 minutes, the water starts
to dispense.
Your next Brew When the brewing
process is complete, the Add Water
indicator LED will illuminate. At this point you
can begin making the next beverage, or you
can power off.
add Water indicator Led
9. The one-time cleaning process is
complete. Discard hot water. Your
brewer is ready to use.
Indicator will illuminate blue – Fill the water
reservoir with cold water until it reaches just
under the rim of the desired level – 6, 8, or
10 ounces (180, 235 or 300 mL) on the
Water Level Guide.
2. Press the Hot Water button. The Add
Water indicator will illuminate.
automatic Shut-off As a safety feature,
your brewer will automatically shut off at any
stage when it is idle for longer than 90
seconds. Press the power button to restart.
If it shuts off while the Brew button LED was
flashing blue, lift and lower brewer handle to
reset.
3. Lift the reservoir lid.
Charcoal Water filter
Your coffeemaker comes with a charcoal
water filter that eliminates chlorine, bad
tastes and odors from tap water.
4. Pour water into the water reservoir until
it reaches the 10 oz. rim on the water
level guide. Close the lid.
inserting the Water filter
1. Remove the filter and filter holder from
the polybag.
2. Soak the filter, fully immersed in cold tap
water, for 15 minutes.
3. Rotate the water filter compartment
cover counterclockwise to remove the
charcoal water filter holder.
K-cup® indicator Led
Indicator will illuminate blue – The blue light
flashes to indicate that the brewing head
needs to be opened and a K-Cup® or My
K-Cup® needs to be inserted. The light will
continue stay on until you lift the brewer
handle.
drip tray overfill indicator
Will pop up when excess coffee that does
not dispense into mug or residual
condensation from the brewing process fill
the drip tray.
5. Lift the brewer handle but do not add a
K-cup®. Water starts to drain from the
water reservoir into the brewer.
8
9
9. Wait until all the water has drained into
the brewer before lowering the brewer
handle completely.
Hot Water
Your brewer is equipped to dispense hot
water to make hot chocolate, tea, soup, and
more.
Brewing
1. Press the Power button.
2. Press the Brew button. Add Water and
K-cup® indicators will illuminate.
to make hot water:
3. Lift the reservoir lid.
4. Pour water into the 10-ounce water
reservoir until it reaches the rim of your
desired fill level on the water level guide
(minimum 6 ounces.) Close the lid.
4. Place the charcoal water filter in the
holder and snap the holder cover
closed. Be careful – improper placement
can tear the filter skin (see figure).
5. Flush the filter and holder by running
fresh water through the hole in bottom
of compartment for 10 seconds.
10. The Brew button LED will remain on,
indicating the water is heating.
6. Allow the filter to drain completely.
note: If Brew button was not pressed
before you added water to the water
reservoir (Brew and Hot Water LEDs are
still flashing) you can do so after water has
drained into the brewer and the brewing
head is closed. The light will now stay on
until heating/brewing is complete.
14. Press the Power button.
15. Press the Hot Water button. Add Water
indicator will illuminate.
5. Lift the brewer handle. Water starts to
drain from the water reservoir into the
brewer.
16. Lift the reservoir lid.
17. Pour water into the water reservoir until
it reaches up to the rim of your desired
fill level on the water level guide
6. Place mug on the drip tray. The drip tray
can be removed to accommodate
travel mugs.
11. After about 2 minutes, the beverage
starts to dispense.
(minimum 6 ounces). Close the lid.
7. Select a K-Cup® portion pack.
Caution: there is very hot water
in the K-Cup® chamber during
the brewing process. to avoid
risk of injury, do not lift the
handle or open the K-Cup®
chamber during the brewing
process.
18. Lift the brewer handle. Water starts to
drain from the water reservoir into the
brewer.
note: Do not remove the foil lid or
puncture the K-Cup®
.
7. Place the assembled water filter holder
into the water reservoir, pushing it down
to fit into place (see figure).
19. Place mug on the drip tray. The drip
tray can be removed to accommodate
travel mugs.
20. Wait until all the water has drained into
the brewer before lowering the brewer
handle completely.
21. The Hot Water button LED will remain
on, indicating the brewer is heating.
note: If the Hot Water button was not
pressed before you added water to the
water reservoir (Hot Water and Brew LEDs
are still flashing) you can do so after water
has drained into the brewer and the brew
head is closed. The LED will now stay on
until heating/brewing is complete.
8. Replace the water filter compartment
cover. Turn it clockwise to close tightly.
*Make sure compartment cover is in
place securely and arrows line up in
order for brewer to brew properly.
8. Place a K-Cup® in the brewing chamber.
Caution: there are two sharp
needles in the brewing chamber
that puncture the K-Cup®, one
above and one below.
to avoid risk of injury, do not put
your fingers in the K-Cup®
brewing chamber.
12. Lift the handle, then remove and
dispose of the used K-Cup®. Close the
brewing head.
note: We recommend changing the water
filter every 60 days or after 60 uses, and
more often if you have hard water.
Replacement filters can be purchased in
stores, by calling Cuisinart Customer Service,
22. After about 2 minutes, hot water starts
to dispense.
Caution: K-Cup® will be hot.
13. Enjoy your cup of gourmet coffee! Your
brewer is ready to use again or you can
power it off.
10
11
2. Disassemble the My K-Cup® by turning
the lid in a counterclockwise direction.
Remove the filter basket from the
holder.
3. Wash the My K-Cup® lid, filter basket
and holder in warm soapy water prior
to use, making sure to rinse and dry
thoroughly. All My K-Cup® parts are
dishwasher safe.
6b. Drop the assembled My K-Cup®
into the brewing chamber. There
is no need to snap it into place.
Maintenance
Any other servicing should be performed by
an authorized service representative.
Brewing with the
My K-Cup® reusable
Coffee filter
The Cuisinart® Compact Single Serve comes
with a My K-Cup® reusable coffee filter,
which allows you to use your own ground
coffee. The dishwasher-safe My K-Cup®
conveniently stores in the easy-open
compartment.
Cleaning the My K-Cup®
reusable Coffee filter
CaUtion: there are two sharp
needles in the brewing chamber
that puncture the K-Cup®, one
above and one below. to avoid
risk of injury, do not put your
fingers in the K-Cup® brewing
chamber.
1. Open the storage compartment located
on the right side of the brewer by
pressing the finger indent. Remove the
My K-Cup®.
2. Disassemble the My K-Cup® by turning
the lid in a counterclockwise direction.
Remove the filter basket from the
holder.
3. Wash the My K-Cup® lid, filter basket
and holder in warm soapy water making
sure to rinse and dry thoroughly. All My
K-Cup® parts are dishwasher safe.
4. Re-insert the filter basket into the holder.
5. Fill the filter basket with ground coffee,
making sure not to fill past the top of
the mesh. Adjust the amount to your
personal preference. Do not tamp the
grounds. Make sure there are no
grounds remaining on the upper rim of
the filter basket. Turn the lid clockwise to
seal.
7. After brewing raise the handle and
remove the My K-Cup®. Use caution
as the My K-Cup® will be hot.
8. Disassemble the My K-Cup® by
turning the lid from the holder in
a counterclockwise direction.
Remove the filter basket from the
holder, discard the grounds and rinse
out the filter basket and holder.
6. Follow brewing instructions on page 10,
but instead of adding a K-cup® place the
My K-cup® in the brewing chamber.
Cleaning the K-Cup® Holder
9. Replace the K-Cup® holder, ensuring
that the arrow on K-Cup® rim aligns with
the arrow on the brewing chamber.
Gently push the K-Cup® holder to snap
into place.
1. The K-Cup® holder is top-shelf
dishwasher safe (use low temperature
cycles in the dishwasher). To remove,
lift the handle to open the brewing
chamber. Grasp the top of the K-Cup®
holder and pull toward you. After
cleaning, replace the K-Cup® holder,
being sure to align the arrow on the
K-Cup® holder rim with the arrow on
the brewing chamber.
1. Before using the My K-Cup® Reusable
Coffee Filter for the first time: open the
storage compartment located on the
right side of the brewer by pressing the
finger indent. Remove the My K-Cup®.
Cleaning and
Maintenance
Cleaning external Parts
We recommend regular cleaning of
the brewer’s external components.
6a. Remove the K-Cup® holder from
the brewing chamber by pulling
toward you. (If you like, store the
K-Cup® holder in the My K-Cup®
storage compartment.)
1. Never immerse the brewer in water
or other liquids. The housing and other
external components may be cleaned
with a soapy, damp, non-abrasive cloth.
2. To remove the drip tray, simply slide it
toward you, keeping it level at all times
in order to prevent spills. The drip tray
and drip tray plate are dishwasher safe.
Do not clean drip tray with cleansers,
steel wool pads or other abrasive
materials.
2. Cleaning the Funnel – The funnel can be
removed from the K-Cup® holder by
pulling on it until it pops off (see figure).
The funnel is top-rack dishwasher safe.
To replace it, just snap it back onto the
K-Cup® holder assembly.
12
13
•
Once the vinegar is dispensed,
discard it into sink.
de-Scaling your Brewer
Mineral content in water varies from place to
place. Depending on the mineral content of
the water in your area, calcium deposits or
scale may build up in your brewer. Though
scale is non-toxic, it can hinder brewer
performance. De-scaling your brewer will
help maintain the heating element and other
parts that come in contact with water.
Step 2: Second Vinegar rinse
•
Pour the remaining 10 ounces of vinegar
into the water reservoir.
•
•
Place the ceramic mug on the drip tray.
Lift the brewer handle, but do not add
a K-Cup®
.
•
After all the vinegar has drained, lower
the brewer handle and press the Hot
Water button.
For optimal performance, de-scale your
brewer every 3 to 6 months. It is possible for
calcium deposits to build up faster, making it
necessary to de-scale more often.
3. Cleaning the Exit Needle –
•
•
The Hot Water button will illuminate blue,
indicating the brewer is heating.
The exit needle is located on the inside
bottom of the K-Cup® holder assembly.
Should a clog arise because of coffee
grounds, it can be cleaned using a
paper clip or similar tool. Remove
K-Cup® holder and insert the paper clip
to loosen the clog and push it out.
Power the brewer off as it starts to
dispense.
•
•
Allow brewer to sit for 30 minutes.
Power on the brewer, lift and lower
brewer handle, then press the Brew
button.
CaUtion: there are sharp
needles that puncture the
K-Cup® above and below. to
avoid risk of injury, do not put
your fingers in the K-Cup®
assembly Housing.
•
Once the vinegar is dispensed, discard
hot contents into sink.
Step 3: fresh Water rinse
• Repeat step 1 three times using
freshwater in place of vinegar
.
note: Before de-scaling your brewer
remember to remove the charcoal water
filter from the water filter holder located in
the water reservoir.
Cleaning the Water reservoir
•
This will clean the brewer plumbing and
remove any residual vinegar taste. The
brewer is now ready for normal use.
It is normal over time for discoloration,
spotting or staining to appear in the water
reservoir. Results will vary depending on the
mineral content of the bottled or filtered
water used but will not affect the operation
of the brewer. However, be sure to clean the
water reservoir regularly to minimize build-
up.
To begin, you will need the following:
•
•
20 ounces of distilled white vinegar
12-ounce ceramic mug (do not use
paper cup)
•
Access to a sink
Clean inside the water reservoir with a
damp, lint-free cloth as necessary.
Step 1: first Vinegar rinse
•
Fill water reservoir with 10 ounces of
undiluted white vinegar.
emptying the internal Water
tank
•
•
Place the ceramic mug on the drip tray.
Lift the brewer handle, but do not add
Brewer must be powered off but plugged in.
a K-Cup®
.
1. Lower the reservoir lid.
2. Place a mug on the drip tray.
•
•
After all the vinegar has drained, lower
the brewer handle and press the Hot
Water button.
3. Press and hold down the Brew button
and continue to hold until all the water is
dispensed into the mug.
The Hot Water button will illuminate blue,
indicating the brewer is heating.
There will be a 3- to 5-second delay before
water begins to dispense.
14
15
If the appliance should become defective within the
warranty period, do not return the appliance to the
store. Please contact our Customer Service Centre:
WARRANTy
LIMITED THREE-yEAR
WARRANTy
troUBLeSHootinG
PROBLEM
SOLUTION:
Toll-free phone number:
1-800-472-7606
Brewer does not have
power.
Plug brewer into an independent outlet.
Make sure the brewer is securely plugged in.
Plug into a different outlet.
We warrant that this Cuisinart product will be free of
defects in materials or workmanship under normal
home use for 3 years from the date of original
purchase. This warranty covers manufacturer’s
defects including mechanical and electrical defects.
It does not cover damage from consumer abuse,
unauthorized repairs or modifications, theft, misuse,
or damage due to transportation or environmental
conditions.
Address:
Cuisinart Canada
100 Conair Parkway
Woodbridge, Ont. L4H 0L2
Email: consumer_Canada@conair.com
Reset your home’s circuit breaker.
Model: SS-300C
Confirm the power has been turned on and the brew and
hot water indicators are flashing.
To facilitate the speed and accuracy of your return,
please enclose:
Products with removed or altered identification
numbers will not be covered. This warranty is not
available to retailers or other commercial
Brewer will not brew.
Turn off and unplug the brewer for 30 seconds or more.
When you plug the brewer back in, be sure to turn the
power back on.
• $10.00 for shipping and handling of the product
(cheque or money order)
• Return address and phone number
• Description of the product defect
purchasers or owners. If your Cuisinart product
should prove to be defective within the warranty
period, we will repair it or replace it if necessary. For
warranty purposes, please register your product
the date of original purchase and keep your original
receipt for the duration of the limited warranty. This
warranty excludes damage caused by accident,
misuse or abuse, including damage caused by
overheating, and it does not apply to scratches,
stains, discolouration or other damage to external
or internal surfaces that does not impair the
functional utility of the product. This warranty also
expressly excludes all incidental or consequential
damages.
If the Add Water indicator is illuminated, check to make sure
the water reservoir is properly filled. If not add desired
amount of water (6 to 10 ounces).
• Product date code*/copy of original proof of
purchase
• Any other information pertinent to the product’s
return
Make sure water has fully drained from the water reservoir
into the brewer by lifting the brewing head.
* Product date code can be found on the underside
of the base of the product. The product date
code is a 4 or 5 digit number. Example, 90630
would designate year, month & day (2009, June
30th).
Make sure the water filter compartment cover is securely in
place by turning clockwise to close tightly.
The exit needle may be clogged (see page 14).
Note: We recommend you use a traceable, insured
delivery service for added protection. Cuisinart will
not be held responsible for in-transit damage or for
packages that are not delivered to us. To order
replacement parts or accessories, call our
Customer Service Centre at 1-800-472-7606. For
more information, please visit our website at
If the Add Water indicator is illuminated even after adding 6
to 10 ounces of water to the water reservoir and water has
fully drained into the brewer, contact Customer Service at
1-800-472-7606.
Your Cuisinart product has been manufactured to
the strictest specifications and has been designed
for use only in 120 volt outlets and only with
authorized accessories and replacement parts. This
warranty expressly excludes any defects or
damages caused by attempted use of this unit with
a converter, as well as use with accessories,
replacement parts or repair service other than those
authorized by Cuisinart.
Chlorine or mineral
taste in coffee.
Consider using bottled water, filtered water or the Cuisinart
Charcoal Water Filer.
Doesn’t brew a full cup. Water may not have fully drained from the water reservoir
into the brewer. Check to see if there is water remaining in
the reservoir. If there is, lift the brewing head to drain water
into the brewer.
Turn off and unplug the brewer for 30 seconds or more.
When you plug the brewer back in, be sure to turn the
power back on.
The exit needle may be clogged (see page 14).
Clean the K-Cup® holder brewing chamber (refer to
“Cleaning & Maintenance” page 13).
De-scale the brewer (refer to page 14).
If you have repeated the de-scaling procedure two times
and it is still brewing only a partial cup, contact Customer
Service at 1-800-472-7606.
Coffee is too weak or
watery.
Consider brewing a smaller cup size or try an Extra Bold
K-Cup®. It has 30% more ground coffee in each portion
pack.
16
17
Blenders
Tools and
Gadgets
Food
Processors
Griddlers
Cookware
Cuisinart offers an extensive assortment of top quality products to make
life in the kitchen easier than ever. Try some of our other countertop
appliances, cookware, tools and gadgets.
©2011 Cuisinart Canada
100 Conair Parkway,
Woodbridge, Ontario L4H 0L2
Any trademarks or service marks of third parties used herein
are the trademarks or service marks of their respective owners.
Printed in China
12CC129218
Keurig, the Cup and Star Design, Keurig Brewed, and K-Cup are trademarks
of Keurig, Incorporated, used with permission. For use and/or licensed under
U.S. Pat. No. 7,165,488; and other U.S. and foreign patents pending.
IB-11021-CAN
|
Mr Coffee ESS11 User Manual
Motorola MOTORAZR 68000202560 A User Manual
Meade Instruments Clock TE109NL M User Manual
LG Electronics Chocolate 3 User Manual
Curtis KCR2610 User Manual
Coffee Maker Aerobie AeroPress User Manual
COBY electronic CR A129 User Manual
Cisco Systems Computer Accessories 3600 User Manual
Black & Decker DCM1375 User Manual
Alpine CDA 9857 User Manual